Vehicles
28 not categorized PORSCHE 987 LOWER ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.92833104306 Known as: control arm lower View/Change Diagram
$4,408.88
Make a selection 115970AAR01 Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more) General FitmentPANAMERA 2010-14
From $324.50
Make a selection 115955AAR01 The Cayenne air-suspension has ride height sensors on all four control arms. General FitmentCAYENNE 2011-14CAYENNE 2007-10 CAYENNE 2003-06
From $324.50
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection 911606105JXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car. Please note: this part number encompasses: Bosch part 0 438 140 045 for 911 SC models from 1977-80 and Bosch part 0 438 140 089 for 911 SC models from 1980-83
$744.70
Make a selection BBI9964010003 Features
$550.00
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,012.23
Make a selection BBI9865010001 Features
$845.00
Make a selection 99750555792 This is a genuine 997.2 GT3 Porsche motorsports cup spoiler lip. It is a cost-effective replacement for the original GT3 spoilers. It also improves front end downforce. Please be aware that it is lower than the original Porsche spoiler but is far more pliable and more curb friendly. This part is shipped in a smaller box by motorsports to conserve on shipping costs. It is manufactured in polyurethane, so it has memory. Once you receive it just lay it out in the sun for an few hours or slowly and carefully warm it up with a heat gun. Please note: all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangea...(choose a part on the right to read more) General Fitment911 GT3 2007-11
$229.00
Make a selection BBI9964010001 Features
$525.00
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection K1347 A good upgrade for slightly modified engines. Convert fuel injected 2.0 engines to weber 40 mm (40 idf) dual throat carbs. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. This kit is for off-road and racing use only, and must never be used on the highways in california. When switching from fuel injection to carburetors, each kits require a lower-pressure fuel pump (part number run7...(choose a part on the right to read more) General Fitment914 1970-76912 1965-69
$1,150.00
Make a selection FVD34791100 Lowering your car without a bump steer kit effectively pulls the steering out of alignment and requires constant steering adjustments that make the car difficult to control. This adjustable bump steer kit will fully compensate to return the steering rack / geometry back to pre-lowered specifications. Our bump steer kit is manufactured to the highest of German standards to ensure the quality, performance and reliability you expect from your Porsche. Features: alloy steel, sealed spherical rod end 14 mm tapered wedge for secure fitment inside the steering arm made for lowering below 30 mm (1.18 inches) / raised spindles allows tie rods to be adjusted downwards no binding throughout suspension travel range finishe...(choose a part on the right to read more) General Fitment911 1970-73
From $284.90
Make a selection K1295 If you are building a high performance 914 engine or have had an engine fire, carburetion is for you! Recommended only for 2.0l engines and big bore engines that are running at least 3/4 cam. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. Kit comes complete with two new 44 idf carburetors, manifolds, linkage, chrome air cleaner, hardware kit and fully illustrated instructions. When...(choose a part on the right to read more) General Fitment914 1970-76
$1,175.00
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection S735012 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper su...(choose a part on the right to read more) General Fitment911 1994-98
$306.90
Make a selection S745012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Sold each, two needed per car. General Fitment911 1994-98
$306.90
Make a selection SPLRTA996 For those who have converted to "true" coilovers in the rear suspension (rear spring relocated over shock) and no longer need the mid link to hold the rear springs, the spl titanium rear toe links replace the stock mid links to provide a wide range of toe adjustment, necessary for lowered cars or for performance alignments. The spl titanium series toe links feature 1.25" 4130 chromoly tubing that is slipped over a cnc machined threaded sleeve then tig welded, making the links extremely strong yet lightweight. The exclusive 4130 chromoly hybrid adjuster offers quick and precise adjustment, and is cnc gundrilled to reduce weight. Blue anodized titanium hardware shaves even more unsprung weight from the arms, w...(choose a part on the right to read more) General Fitment911 1998-05911 TURBO/GT2 2001-05 BOXSTER 1997-04 CAYMAN 2006-08
$876.15
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection
$11.26
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection
$1.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |